hi!
As the native motor 2.3SHC has appeared to be repaired it is unreal (may be after...) that I have bought the motor 2,8i. (but I can't use MFI or EFI on my funny old 20M :)
Has started to assemble the motor, and has a problem - I cannot find in sale intake manifold from the engine with carburetor in any way. Many 2.8 have MFI or EFI - not a carburetor :(
I have found number intake manifold 2,8: F0142538 - is right?
Photos:
My "new" motor block 2.8 v6 in cleaning stage :),
crankcase from V6 P7B - for use it with 2,8.
Intake manifold. may be somebody have one for sale?
Thanks.
Greetings,
Roman
PS
Also, somebody put this carburettor on such motor?:
http://cgi.ebay.de/42-er-WEBER-Hochleistung-Doppel-Fallstrom-Vergaser_W0QQitemZ320107964338QQihZ011QQcategoryZ33550QQrdZ1QQcmdZViewItem
I think to buy it... This is new, not a repaired, as I know.
rtype 
/ 2007-04-28 21:59:36 /
A right 'number" is FO 142536. This is Firing Order - order in witch spark is distributed to plugs.
Original intake manifold from 2.8 v6 PYA is very difficult to buy in Poland, but is possible. Original carburator in PYA was solex 38/38 EEIT. Price of this used kit is about 100-200€. See also ads in our market http://www.capri.pl/services/market
Mysza liil (EM) / 2007-04-29 07:51:40 /
If you need i have Intake manifold to 2.8 for sale also i have this Weber carburator and this i can sale too. For more info write to my email
CHUDER 
/ 2007-04-29 09:10:48 /
Thanks for answer!
>This is Firing Order - order in witch spark is distributed to plugs.
Oh! I'm don't thinking about that :D :D :D Thanks. (ha ha ha - I'm stupid :) :) ;)
Now number is absent...
>Original intake manifold from 2.8 v6 PYA is very difficult to buy in Poland, but is >possible.
>Original carburator in PYA was solex 38/38 EEIT.
Yes, I think, but all of them is not in good condition, may be new carb is a more good way...
>Price of this used kit is about 100-200€.
This is really correct cost.
The carburettor separately costs 30-80EU (about condition),
refubrished carb 100-160 (like new), an intake manifold near 60-80.
>See also ads in our market http://www.capri.pl/services/market
Tam po polski, ya mnogie slowa ponimauy, no terminy polskie ne vse znauy :(
potomu poisk zatrudnen.
:)
Greetings,
Roman
rtype / 2007-04-29 09:16:18 /
to CHUDER:
I wrote message to you. Closely I wait the answer :)
Roman
rtype / 2007-04-29 12:04:06 /
hi!
The question is still opened...
Roman
rtype / 2007-04-30 08:49:13 /
If you can't wait until you find original 2.8 V6 intake manifold and carburettor then you may also fit 2.3 V6 intake manifold + carburettor. It's not the same but it will run.
Murphy's law says that you will find a complete 2.8 V6 kit as soon as you fit the 2.3 kit. :-)
Rafał L. / 2007-05-06 00:01:06 /
hi!
Thanks. I know about 2.3 intake and have not one :)
At the moment I order intake from England. I have bought(purchased) there parts to the motor (on ebay), and the seller has kindly offered me by inquiry other parts. Including intake. Certainly cost of transfer will be decent, but in the sum intake will leave $80-100. I consider it reasonable by. All the same while different orders come, and I cannot start to build the motor. Just and this order will come. :)
ebay rulezz :)
rtype / 2007-05-07 21:11:37 /